Spam Fighting: To Bounce or Not to Bounce?
Even if you've tuned your spam-fighting arsenal to perfection, you've still got a big problem. Namely, what do you do with all that undeliverable spam? Here are a few ideas.
What is the largest headache caused by spam? Many sites find that once you get decent filtering in place and start identifying spam, a new problem that crops up is just a disconcerting: Deciding what to do with it.
Software such as amavisd-new, a front-end for SpamAssassin and virus filters, leaves the ultimate decision up to the administrator. That is, what do we do with e-mail that has been identified as spam? The options are: use before-queue filtering to not accept it in the first place, send a delivery status notification (DSN) notifying the party that their e-mail was not delivered, or just silently discard the email. All of these options have consequences, and some are more hair-raising than others.
Option 1: DSNs, aka Bouncing
In this first scenario, a mail server will accept most email, and then subject it to spam and virus filtering before delivering it to a user's mailbox. If the e-mail is determined to be spam, it isn't delivered to the user, and a DSN is sent to the address in the From: header, notifying the sender that delivery was not successful.
This is problematic for many reasons. Most critical, is the fact that the From: header in spam is rarely correct. In fact, it is possibly claiming to be from someone you know, since spammers have been known to harvest e-mail addresses from people's address books. Sending a DSN to someone who didn't send e-mail in the first place causes confusion, and results in support calls from the confused user who thinks their e-mail account has been compromised.
Even more detrimental to productivity, sending DSNs to addresses or domains that don't exist will cause the bounces to pile up on the mail server, since they can't be handed off to another server. Thousands of e-mail messages sitting in the mail queue will jeopardize system resources and can effectively clog mail services for legitimate mail. Most organizations find this to be the most difficult aspect of dealing with spam.
Option 2: Silently Discarding
Once a message has been accepted and eventually identified as spam, another option is to simply discard the message. This completely solves the problem of a mail server crumbling from having too much mail in the queue, but is perhaps just as problematic. If e-mail is falsely identified as spam, and the sender isn't notified that delivery failed, the sender will just assume everything was delivered as usual.
Clearly this is less than optimal, but when servers start falling over due to extensive resource consumption, many people turn to silently dropping spam. Oftentimes, silently discarding e-mail is an intermediate step between DSNs and before-queue filtering. David Ernst of HoosierNet said it was a question of keeping the mail flowing at all. "Well," he noted, "something had to be done. We can grind the service to a halt if we try to process all of those return-to-senders. So, it made the difference between working and not working."
Many people in this position opt to use a hybrid system of still sending DSNs, but cleaning the queue periodically to discard ones that cannot be sent.
Option 3: Don't Accept it at All
Ideally we want to identify spam while the sending server is still connected, and tell them that delivery isn't going to happen. This means that the sending server has to deal with it, and in the case of a spammer, it simply means that sending failed. "Just don't accept it" is quite easy to say, but sometimes tricky to implement.
Some mail servers, such as postfix and sendmail, have the ability to hand messages to another program before sending them to the queue for final delivery. This provides the ability for the second program to scan mail for viruses and spam, and report the status to the mail server. If the message is identified as spam, the server, which has not yet reported to the sending server "delivery accepted," now has the option of reporting an error. There is no need to send a DSN, since we never accepted the suspicious message in the first place.
Implementing spam and virus checking isn't very difficult. Depending on the mail server, implementing spam filtering such that it is able to reject spam before the SMTP session is over can be difficult. Two widely used mail servers, postfix and sendmail, both have the ability to utilize amavisd-new. Amavisd-new is a favorite, since it provides a nice and simple way to implement spam and virus checking, so we feel it deserves special mention.
Sendmail has the milter interface, which allows anyone to program add-ons to sendmail. The amavis-milter will hand off mail to amavisd-new, which in turn runs SpamAssassin and virus checking. Amavisd-new will also check attachments, and can extract data from zip files and many other types of archives to check for viruses and spam. Configuring this in postfix is even simpler, since it only requires one change in the configuration file, plus the addition of another smtpd process.
Email is increasingly frustrating to manage. We sometimes want to receive messages from people we don't know, so e-mail is designed to reflect that. People have implemented systems where a sender has to verify himself the first time they send email, but that type of system doesn't always work. For instance, users always want to receive automated messages when they purchase things online, and those messages are normally sent from an address that people don't monitor, making "sender verification" impossible.
One thing that's clear is that sending DSN messages for spam is very bad practice. Users are confused when they receive a DSN for mail they didn't send, and dropping spam silently will lead to lost email. The best option is to complete all virus and spam checking before accepting the mail for delivery, then report "success" to the sending server. Aside from the fact that this option tends to make the most sense, in most cases it also conserves system resources.