Troubleshooting Checklist for 802.1X on Your WLAN

By Eric Geier | Jan 7, 2011 | Print this Page
http://www.enterprisenetworkingplanet.com/netsecur/article.php/10952_3919916_2/Troubleshooting-Checklist-for--8021X-on-Your-WLAN.htm

WPA/WPA2-Enterprise with 802.1X authentication provides secure and robust Wi-Fi security for businesses. Though 802.1X isn't the easiest protocol to implement, it should be a must for all organizations with more than a couple of employees using the wireless network. In this tutorial, we'll discuss how to troubleshoot 802.1X client issues.

Verify Client Settings

The 802.1X settings on the client is a frequent trouble spot and is likely the cause if the problem is isolated to a single client. You should verify all encryption and authentication settings are correctly configured.

If the client is using Windows with a third-party wireless connection manager and/or 802.1X supplicant, you might want to disable or uninstall them and revert to using Windows. If the client is another OS or mobile device, you should verify settings similar to those discussed here.

In Windows, bring up the network profile or properties window (figure 1 shows an example) and start by verifying you have selected the right authentication and encryption settings. For instance, WPA with TKIP or WPA2 with AES, depending upon which is supported by your access points (APs).

In Windows 7, you'll also find an Advanced button on the Security tab of the Wireless Network Properties window. Click it and verify those settings, such as seen in figure 2. One key setting is the authentication mode. If you're unsure about it, select User or computer authentication.

Next verify the right authentication method: Protected EAP (PEAP) or Smart Card or other certificate for EAP-TLS. If you're using a third-party supplicant instead of the one built into Windows, make sure it's selected.

Next, open the Protected EAP (PEAP) or Smart Card or other certificate settings by clicking the Settings button in Windows Vista and 7 or clicking the Properties button in Windows XP. Figure 3 shows an example of the Protected EAP (PEAP) settings and figure 4 of the Smart Card or other certificate settings.

For either authentication method, verify the selected server certificate. Double-click on it to verify it's the right one and not expired. If you have a server specified in the Connect to these servers field, consider disabling that option for now to see if that might be the issue. Furthermore, you might uncheck the Validate server certificate option temporally to see if the problem might be related to the server certificate. Just remember to re-enable it later for security reasons.

If using Protected EAP (PEAP), ensure the Secured password (EAP-MSCHAP v2) option is selected on the Properties dialog. Then click the Configure button to verify the setting (see figure 5), which should only be selected if the user credentials on the RADIUS server match the Windows account credentials.

If using EAP-TLS with a Smart Card or certificate, verify the settings on the Properties dialog. If using certificates, make sure it's properly installed on the computer via the Microsoft Management Console (MMC).

After you've verified the settings, you might try connecting again. If using PEAP, be sure to use the correct username and password, and domain if required.

One last client setting you might want to check is the system date and time in Windows. An incorrect date or time can be a problem since the server and user certificates are time-sensitive.

Check RADIUS Server

If you've verified the client settings and are still having problems you might want to check the RADIUS server, whether you're running IAS or NPS on a Windows Server, FreeRADIUS, or another authentication server. Verify it's up and check the logs to see if there are any clues. Also verify that the user database and any other required databases are running.

If all or many clients are having issues, the problem likely is with the authentication server. If you have a smaller network it may take awhile to see issues with more clients, as they will at least remain connected to the wireless LAN until they try to authenticate with the server again.

Check Access Point or Switch

You may want to check the wireless access point (AP) or switch that the problem client is connecting through. If the problem seems to be through a particular AP or switch, double check the IP address to what you have setup in the RADIUS server. Remember you must assign static IPs to the APs and switches since that is how the RADIUS server identifies them. Also verify the corresponding Shared Secret and other authentication settings on the AP or switch.

General Network Issues

Sometimes the problem might not even be related to 802.1X and just be a basic networking issue. Double-check that the problem client is connecting to the correct SSID. If you're connecting an older 802.11b client to an 802.11n network, it might not work even though the two standards to suppose to be compatible. Also ensure the compatibility of the network adapter and operating system with WPA or WPA2 encryption.

If it's an older adapter, you can try to download and install an updated driver that might give you better interoperability and/or WPA/WPA2 support.

You may also find that the operating system is lacking WPA or WPA2 support. For Windows XP without any Service Pack installed, an update is available for adding WPA support. For Windows XP or Windows XP Service Pack 2, an update is available for adding WPA2 support. Windows XP Service Pack 3 contains both of these updates already.

Review User Settings and Attributes on RADIUS Server

If you've already verified the client settings and think this is an isolated issue, you might want to review the settings and attributes assigned to that specific user on the RADIUS server.

If you've assigned any custom attributes, you may want to disable them to see if they might be causing an issue. For example, you may have limited access to specific access points or switches with the NAS-Identifier or Called-Station-Identifier, or limited access from specific network adapters with the Calling-Station-Identifier. Most RADIUS servers also let you set login-times and an expiration date/time, which might cause an issue. If using VLANs, you might see if there are any problems there.

Perform Tracing and Review Client Logs

If the client is running Windows, you can use the tracing features of the Netsh command-line tool to help identify the underlying issue. For tracing of various networking components in Windows XP or later, you can use the netsh ras commands. In Windows Vista or later, you can perform wireless tracing with the netsh wlan commands.

If you're using a third-party 802.1X supplicant, you might check any available logs.

Conclusion

We discussed the key methods of troubleshooting 802.1X client issues. If you're now questioning 802.1X, keep in mind these 15 reasons to use 802.1X. You might also want to check out another piece that discusses overcoming the common 802.1x deployment issues including simplifying client configuration.


Eric Geier founded NoWiresSecurity, which helps businesses quickly and easily protect their Wi-Fi with enterprise-level security. He's also a freelance tech writer and author of many networking and computing books, for brands like For Dummies and Cisco Press.